CBI-electric -- Part Number Configurator

TYPE

Description

D2 - D-Frame DD -Type

Note

MOUNTING

Description

A - Front mount square aperture standard type

C - Front mount round aperture fleet

D - Centre lock mounting

S - Front mount square aperture

Z - Special specify

G - DIN rail and surface mount

Comments

See figure 1.1

See figure 1.2

Note

HANDLE OR POLE BLANK

(Reduced Handle)

Description

A - Standard handle

C - Cut off handle

E - Baton handle (centre lock mount only)

H - Flush rocker handle

M - Two tone flush rocker handle

W - No handle, Blank front plate

2 - Standard handle, mid trip

4 - Cut off handle, mid trip

6 - Two tone flush rocker handle, mid trip handle pull to reset

Z - Special specify

Q - Push to reset handle

R - Two tone push to reset handle

0 - No handle, raised blank front plate

7 - Two tone rocker handle, mid trip

Comments

See figure 2.1; for mountings A, B

Note

MAIN TERMINAL DESCRIPTION

Description

AX - M5 or 10-32 stud

MX - M6 or 1/4-20 stud terminals

2X - Plug in terminal (Dia 6.25mm X 21.5mm)

3X - Plug in terminal (Dia 7.80mm X 21.5mm)

4X - M5 or 10-32 flush rear screw terminal

V1 - Bridge terminal for 2 pole parallel construction (On M6 or 1/4-20 stud terminal)

W1 - Bridge terminal for 3 pole parallel construction (On M6 or 1/4-20 stud terminal)

ZZ - Special specify

5X - Double quick connect terminal (0.8mm X 6.35mm)

XX - No terminal

Comments

Note

NUMBER OF POLES

Description

1 - 1 pole metric

2 - 2 pole metric

3 - 3 pole metric

4 - 4 pole metric

5 - 5 pole metric

6 - 6 pole metric

A - 1 pole imperial

B - 2 pole imperial

C - 3 pole imperial

D - 4 pole imperial

E - 5 pole imperial

F - 6 pole imperial

Note

RATED VOLTAGE AND FREQUENCY

Description

J - 240V 50/60Hz

K - 277V 50/60Hz

N - 80V DC

S - 120/240V 50/60Hz

Q - 240/415V 50/60Hz

R - 277/480V Hz

M - 80V DC / 240V 50/60Hz

L - 80V DC / 277V 50/60Hz

Z - Special specify

P - 80V DC / 120V 50/60Hz

B - 24V DC

C - 32V DC

D - 50V DC

E - 65V DC

F - 125/250V 50/60Hz

G - 250V 50/60Hz (1 Phase Common Bus At 250V)

H - 125V DC

Comments

Common bus at 240V

Common bus at 277V

2 wire centre tap supply, 120V per phase

3 phase multi wire system

AC/DC version

Note

TIME DELAY

(For details of time delay refer to the application guide)

Description

AS - Long Time Delay 50/60Hz or DC

AI - Long Time Delay 50/60Hz or DC (AS + Inertia Delay)

AH - Long Time Delay 50/60Hz

AE - Long Time Delay 50/60Hz (AH + Inertia Delay)

BS - Medium Time Delay 50/60Hz or DC

BI - Medium Time Delay 50/60Hz or DC (BS + Inertia Delay)

BH - Medium Time Delay 50/60Hz

BE - Medium Time Delay 50/60Hz (BH + Inertia Delay)

CS - Short Time Delay 50/60Hz or DC

CI - Short Time Delay 50/60Hz or DC (CS + Inertia Delay)

CH - Short Time Delay 50/60Hz

CE - Short Time Delay 50/60Hz (CH + Inertia Delay)

US - Ultra Short Time Delay 50/60Hz or DC

OP - Instantaneous Trip 50/60Hz or DC

AD - Long Time Delay 50/60Hz/DC

BD - Medium Time Delay 50/60Hz/DC

CD - Short Time Delay 50/60Hz/DC

AW - Long Time Delay 50/60Hz/DC (AD + Inertia Delay)

BW - Medium Time Delay 50/60Hz/DC (BD + Inertia Delay)

CW - Short Time Delay 50/60Hz/DC (CD + Inertia Delay)

OX - Switch 50/60Hz or DC

ZZ - Special specify

H3 - Short Time Delay 50/60Hz or DC

Comments

8 x In

20 x In

35 x In

8 x In

20 x In

35 x In

6 x In

15 x In

35 x In

8 x In

20 x In

15 x In

6 x In

System

AC or DC

AC and DC

AC or DC

Pulse Tolerance

8 x 1n

20 x 1n

35 x 1n

8 x 1n

20 x 1n

35 x 1n

6 x 1n

15 x 1n

35 x 1n

None

8 x 1n

20 x 1n

15 x 1n

6 x 1n

Note

MAIN CIRCUIT CURRENT

Description

0050 - 0.5A

0100 - 1A

0130 - 1.3A

0150 - 1.5A

0200 - 2A

020M - 20mA

0250 - 2.5A

0300 - 3A

0350 - 3.5A

0400 - 4A

0420 - 4.2A

0500 - 5A

050M - 50mA

0600 - 6A

0700 - 7A

0750 - 7.5A

0800 - 8A

1000 - 10A

100M - 100mA

1100 - 11A

1200 - 12A

1300 - 13A

130M - 130mA

1350 - 13.5A

1400 - 14A

1500 - 15A

1600 - 16A

160M - 160mA

1700 - 17A

2000 - 20A

200M - 200mA

2300 - 23A

2500 - 25A

2600 - 26A

3000 - 30A

300M - 300mA

3200 - 32A

3500 - 35A

4000 - 40A

420M - 420mA

4500 - 45A

4800 - 48A

5000 - 50A

500M - 500mA

6000 - 60A

6300 - 63A

6500 - 65A

6700 - 67A

7000 - 70A

7500 - 75A

8000 - 80A

800M - 800mA

8500 - 85A

9000 - 90A

K100 - 100A

K110 - 110A

K120 - 120A

K125 - 125A

K140 - 140A

K150 - 150A

K160 - 160A

K170 - 170A

K175 - 175A

K180 - 180A

K185 - 185A

K200 - 200A

K240 - 240A

K250 - 250A

K300 - 300A

K350 - 350A

K400 - 400A

K600 - 600A

XXXX - No Current, for Voltage Trip Poles

Note

CIRCUIT CONFIGURATION

Description

AX - Switch

BX - Series Trip

CA - Relay Trip Current Sensing, Offset Terminal Construction

CX - Relay Trip Current Sensing,Centre Terminal Construction

DA - Relay Trip Voltage Sensing, Offset Terminal Construction

DX - Relay Trip Voltages Sensing, Centre Terminal Construction

EA - Shunt Trip Current Sensing, 3rd Terminal Close To Line Side

EX - Shunt Trip Current Sensing, 3rd Terminal Close To Load Side

FA - Shunt Trip Voltage Sensing, 3rd Terminal Close To Line Side

FX - Shunt Trip Voltage Sensing,3rd Terminal Close To Load Side

G2 - Dual Control-Relay Trip Construction, Mid Trip Handle And Trip Alarm Switch

GA - Dual Control - Shunt Trip Construction (3 Terminal),3rd Terminal Close To Line Side

GX - Daul Control-Shunt Trip Construction (3 Terminal),3rd Terminal Close To Load Side

H1 - Dual Control-Relay Trip Construction with Auxiliary Switch

H2 - Dual Control - Relay Trip Construction, Mid Trip Handle And Trip Alarm Switch

HX - Dual Control-Relay Trip Construction (4 Terminal)

JX - Switch With Auxiliary Switch

KX - Series Trip with Auxiliary Switch

LA - Series Trip, Mid Trip Handle

LB - Series Trip, Mid Trip Handle with Aux Switch

LX - Series Trip, Mid Trip Handle with Trip Alarm

MX - Series Trip ,Trip Alarm (Latch Type-Reversed Function)

NX - Series Trip Voltage Sensing

PX - Series Trip Voltage Sensing with Micro-Switch

QX - Series Trip Voltage Sensing with Mid Trip Handle & Trip Alarm

XA - Neutral

XB - Neutral with Auxiliary Switch

XC - Neutral with Mid Trip Handle & Trip Alarm

ZZ - Special Specify

Comments

50A max for the sensing coil; total current 100A max

Total load 100A maximum

Voltage coil normally at line voltage; No AH, BH, CH, AE, BE, CE

Flying leads

For voltage coil

No AH, BH, CH, AE, BE, CE

Trip alarm required mid trip handle

Note

AUXILIARY AND ALARM SWITCHES

Description

6 - Auxiliary Switch Actuator Fitted

A - One Change Over Gold Plated Tips, Equally Spaced Terminals

B - One Change Over Silver Tips, Equally Spaced Terminals

C - One Change Over Silver Tips, Offset Terminals

D - One Change Over Gold Plated Tips, Offset Terminals

E - Micro Switch Reversed Termination, Gold Plated

M - Integrated Micro Switch Housing (Parallel Bridge)

X - Flat Baseplate No Micro Switch

Z - Special Specify

Comments

0.02 to 0.1A Max 30V

See figure 3.8 and figure 3.9

Note

VOLTAGE AND CURRENT COIL RATINGS

Description

A1 - 12V AC 50/60hz

A2 - 24V AC 50/60hz

A3 - 65V AC 50/60Hz

A4 - 110-125V Ac 50/60Hz

A5 - 220-240V AC 50/60hz

A6 - 6 - 277V AC 50/60Hz

B0 - 12V DC

B1 - 24V DC

B2 - 48V DC

B3 - 80V DC

B4 - 6 - 125V DC

C1 - 20mA

C2 - 100mA

C3 - 1A

C4 - 0.1 - 20A

XX - Not Applicable

ZZ - Special Specify

Note

TERMINAL FOR SHUNT, RELAY AND DUAL CONTROL CONSTRUCTION

Description

B - M5/10-32 screw terminal

C - Quick connect terminal

E - M5 / 10-32 studs

X - Not applicable

Z - Special specify

D - Fly leads

F - M6 / 1/4-20 studs

Comments

Figure 12.1; 50A max.

Figure 12.2; 25A max.

Figure 12.3; 60A max.

Exiting on side, not rear

Note

VOLTAGE FOR ILLUMINATED ROCKER

Description

X - Not applicable

Note

For illuminated handle versions please contact your nearest CBI office for assistance

TERMINAL FOR ILLUMINATED ROCKER

Description

X - Not applicable

Note

For illuminated handle versions please contact your nearest CBI office for assistance

FRONT PLATE COLOUR AND MARKING OPTIONS

Description

A - Black front plate standard marking

2 - Black front plate no marking, with test button for mechanical trip

Z - Special specify

B - Black front plate no marking

1 - Black front plate std marking with test button

Comments

I-0, ON-OFF and Amp rating

Test button is standard on mid trip rocker handle version

Note

INTER-PHASE BARRIER AND TERMINAL COVER

(Interphase barriers and terminal covers are required for UL listed Approvals)

Description

A - Small inter-phase barrier

B - Large inter-phase barrier

C - Z Inter-phase barrier

1 - Terminal cover(s)

2 - Small inter-phase barrier and terminal cover (UL 1077 only)

3 - Large inter-phase barrier and terminal cover

4 - Z inter-phase barrier and terminal cover

X - Not applicable

Z - Special specify

Note

Interphase barriers and terminal covers may be required for multi-pole products that have UL listed approvals and UL recognized approvals. See the application guide for the D/DD frame for details, or contact your nearest CBI sales office for assistance.

APPROVALS AND TYPICAL SAFETY MARKS

(Standard marks and approval basket covers most regions)

Description

1 - UL1077 recognized, CSA, VDE

2 - UL489 Listed, CSA, VDE

3 - UL489A Listed, VDE

4 - UL1077 recognized, CSA

A - UL1077 Recognized only

Z - No approvals

5 - UL1077 Recognized, UL1500 Certified

6 - VDE Certified For Railway Application, CE

B - CE Compliant

Comments

For VDE, CE normally IEC/EN60934

For VDE, CE normally IEC/EN60947-2

Note

OPTIONAL SAFETY MARKS

Description

C - CCC / CRCC

X - Not applicable

Z - Special specify

Comments

Required for products exported to Peoples Republic of China

Note

Only required in specific cases where import into the country is prohibited, unless the product carries the mark.

HANDLE COLOUR

Description

G - Green, Green Indicator / Black Face

W - White, Black Indicator / White Face

B - Black

4 - Blue, Blue Indicator / Black Face

Y - Yellow, Yellow Indicator / Black Face

R - Red, Red Indicator / Black Face)

F - Grey

J - Orange

X - No handle on this Pole

Z - Special specify

Note

The coding is dependent on the type of handle. For all handles excluding the flush rocker and two tone flush rocker handles, the colour code describes the colour of the handle. For the flush rocker handle the colour code describes the colour of the on and off actuation buttons by a single code.
The two tone flush rocker handle the colour code describes the indication colour. The face colour is black and the indicator indicates the off or tripped position (see figure 2.7).
After picking the appropriate colour code pick the marking code. The marking colour of the two tone flush rocker handle is equivalent to the indicator colour. After picking the appropriate marking the direction of print may be specified. For the toggle handle types only codes V and H are applicable (see figure 15.1). If the pole has no handle because of it being a reduced handle version use code XXX.

HANDLE MARKING

Description

A - Blank, No marking

B - I - 0

C - ON - OFF

D - I - 0 and ON - OFF

X - No handle

Z - Special specify

I - Push to reset and amp rating

Note

HANDLE ORIENTATION

Description

V - Vertical (V) (Standard Mounting , Line at Top)

H - Horizontal (H) (Line at Left)

1 - Vertical (1) (Reversed Mounting , Line at Bottom)

2 - Horizontal (2) (Line at Right)

X - No handle

Z - Special specify

Comments

See figure 15.1 (line side at the top)

See figure 15.1 (line side to the left)

See figure 15.1 (line side at the bottom)

See figure 15.1 (line side to the right)

Note

Part Number Configurator - DD Frame

TYPE

MOUNTING

HANDLE OR POLE BLANK

MAIN TERMINAL DESCRIPTION

NUMBER OF POLES

RATED VOLTAGE AND FREQUENCY

TIME DELAY

MAIN CIRCUIT CURRENT

CIRCUIT CONFIGURATION

AUXILIARY AND ALARM SWITCHES

VOLTAGE AND CURRENT COIL RATINGS

TERMINAL FOR SHUNT, RELAY AND DUAL CONTROL CONSTRUCTION

VOLTAGE FOR ILLUMINATED ROCKER

TERMINAL FOR ILLUMINATED ROCKER

FRONT PLATE COLOUR AND MARKING OPTIONS

INTER-PHASE BARRIER AND TERMINAL COVER

APPROVALS AND TYPICAL SAFETY MARKS

OPTIONAL SAFETY MARKS

HANDLE COLOUR

HANDLE MARKING

HANDLE ORIENTATION